Sonifex Software
RB-PD2 Firmware Versions
RB-PD2 V1.051
- Bug fixes:
- Fixed incorrect channel status settings in digital transceiver which didn't transfer receive channel status to transmit.
- Fixed bug in digital transceiver setup for Analogue Sync and Digital modes where unit would use invalid clock.
RB-PD2 V1.046
- Alterations
- Added support for revision 9+ PCB which includes new audio clock generation device
- Removed unused peripheral code
RB-PD2 V1.045
- Alterations
- Change to allow multiple dump operations in quick succession - applies to dump buffer only
- Improved delay start to minimise muted output when performing a drop
- Bug fixes:
- Fixed CF mount errors by allowing retries until device becomes ready
- Fixed review mode bugs when CF delay/dump file selected
RB-PD2 V1.043
- Bug fixes:
- Fixed SCi lockup when building delay
RB-PD2 V1.042
- Alterations
- Added small dump hold off when building/exiting delay
RB-PD2 V1.041
- Bug fixes:
- Added System Mode with normal and new review mode
RB-PD2 V1.040
- Bug fixes:
- Changed rotary encoder code to filter false triggering
RB-PD2 V1.039
- Bug fixes:
- Delay set by the serial command did not update internal delay value. Subsequent changes using the encoder could then show the wrong value
RB-PD2 V1.038
- Alterations
- Serial code changed to return ACK instead of NAK if config settings are overwritten with same setting.
- Added test record (TEST0001.WAV) select by de-pressing debug button when selecting new recording.
- Added serial commands to set remote input and output functions collectively:
- For inputs: “SAI:1_2_3_4_5_6_7_8” where 1-8 is setting for each remote input.
- For outputs: “SAO:1_2_3_4_5_6” where 1-6 is setting for each remote output.
- Added serial full reset command.
- Bug Fixes:
- Changed sequence for serial record command to fix problem with locking to digital input after recording completes.
- Current delay display cleared for serial clear delay command.
RB-PD2 V1.037
- Alterations
- When at selected delay, using Cough multiple times to decrement delay to zero occasionally caused the delay to loop below zero.
RB-PD2 V1.034
- Alterations
- Exit delay fails after delay is acquired using play file start mode (first time only)
RB-PD2 V1.033
- Alterations
- When delay is at or close to zero, pressing the dump button caused the delay value to loop below zero
RB-PD2 V1.026
- Alterations
- Changed initial transition into building delay to smooth out the effect on the audio
RB-PD2 V1.025
- Alterations
- Reading BWF files with larger chunk sizes caused address error and system crash
RB-PD2 V1.024
- Alterations
- Using cough or dump buffer when delay is greater than 0.2 seconds causes intermittent channel swap
RB-PD2 V1.023
- Alterations
- Added new field in SCI status request command to show when memory card is loaded
- Changing sample rate & sample width from SCI didn't update display with new value
- Drop command from SCI failed to initiate dump first
- New folders incorrectly created on memory card when SCI commands GDL and GFL received
- Display didn’t show new delay duration when changing start mode from play file to build delay
- Setting delay time above 9.9 seconds failed when using SCI
- Display didn’t show new delay duration when changing start play file
RB-PD2 V1.019
- Alterations
- Press and hold bypass button switches bypass on then off after short delay
- Prevented activation of cough whilst start play file or dump play file actively playing
- Crash when exiting delay and dump file is played
RB-PD2 V1.017
- Alterations
- Prevent formatting of memory card when either start play file or dump play file modes are selected
- Prevent deletion of files on memory card selected for either start play file or dump play file
- Prevent recording whilst delay is active
RB-PD2 V1.014
- Alterations
- Prevented activation of dump/drop whilst start play file actively playing
- Active directory reset to root when recording new files
RB-PD2 V1.013
- Alterations
- Crash when memory card removed whilst start play file or dump play file modes is selected or active or record is active
RB-PD2 V1.012
- Alterations
- Prevented activation of exit delay whilst cough is active
RB-PD2 V1.011
- Alterations
- Pressing cough whilst exiting delay when delay is less than 0.2 seconds caused audio error
- Digital input synchronization modified to prevent false unlock conditions
RB-PD2 V1.010
- Alterations
- Digital input synchronization incorrectly locked to sample rates above 48 kHz
RB-PD2 V1.009
- Alterations
- Digital input synchronization fails when SCI is connected
RB-PD2 V1.008
- Alterations
- Prevented activation of exit delay whilst dump is active
RB-PD2 V1.007
- Alterations
- Changed mapping of display due to increased size of menu data
RB-PD2 V1.006
- Alterations
- Added new remote mode for delaying remote inputs to outputs using current delay
RB-PD2 V1.005
- Alterations
- Error when initiating and releasing drop twice whilst dump active
RB-PD2 V1.004
- Alterations
- Releasing drop before play dump ends causing indeterminate state
- Current delay reset to zero when playing dump file whilst exiting delay
RB-PD2 V1.003
- Alterations
- Added audio loop through when recording
RB-PD2 V1.002
- Alterations
- Audio channel swap on delay exit when approaching zero delay
RB-PD2 V1.001
- Alterations
- Compact flash becomes full whilst recording and system crashes
RB-PD2 V1.001
- Initial release
