Sonifex Software
AVN-CU1 Firmware Versions
1.0.2667
4 September 2024
New
-
Initial Release
AVN-CU2 & AVN-CU4 Firmware Versions
3.16.2646
14 June 2024
Fixed
- Improvements to frontpanel firmware to help fix occasional white screen on startup.
- Note: While installing this firmware, the screens will remain blank for longer while the firmware on the front panels are upgraded.
- During this time (which can be up to 3 minutes on the AVN-CU4), do not switch off the unit.
3.15.2626
18 March 2024
Fixed
- Encoder setup tabs on audio routing page not showing for all inputs and outputs
3.14.2615
8 February 2024
Fixed
- AVN-CU4: Buttons 23 and 24 do not work if configured as User buttons for GPIO events.
3.12.1.2568
29 September 2023
Fixed
- Incorrect frontpanel binary.
3.12.2523
18 July 2023
Fixed
- Fixed a bug in which Dante network settings were not applied when changing them via the web UI or frontpanel.
3.11.2468
13 January 2023
Fixed
- LED colour balance corrected for specific hardware variant.
3.10.2434
4 November 2022
Fixed
- Frontpanel brightness not initialised correctly on some units.
3.9.2409
22 September 2022
Fixed
- Mix-point encoder information on webpages not updated correctly when changing the names of inputs and outputs.
- Phantom power enable/disable menu on frontpanel not updated correctly when switching commentator input between mic and line modes.
3.8.2405
20 September 2022
Fixed
- Front panel initialisation issues.
- Backlight flashing during startup.
3.5.2372
23 May 2022
New
- Enabled on startup option can now be selected in the button configuration menu of the front panel webpage.
- Signal detection on digital, analogue, and Dante audio inputs. A presence threshold and presence timeout can be selected within the general tab of the input configuration window. A signal presence event can then be added on the GPIO settings webpage, allowing it to be routed for example to a GPO or talkback notify event.
- Headphone ducking can be configured in the general tab of the headphones configuration window (accessed via the audio routing webpage). The ducking level (the amount to reduce the audio level by) can be setup in the configuration window. On the GPIO settings page the headphone ducking event can be add to the output section, allowing the headphone audio to be ducked for example by a GPI or a signal presence event. Note that when using the signal presence event to trigger the ducking event the audio on the signal presence input remains at the normal level whilst any other audio is reduced by the ducking level.
- A talkback notify event can be added to the output section of the GPIO routing grid (on the GPIO settings page), this allows for example a GPI or signal presence event to be used to trigger the talkback notify event, this will then cause the corresponding talkback button on the front panel to flash.
- Encoders in the same encoder position (row) but on different encoder pages can now be "ganged" this allows an encoder on one page to also control the level, pan, and mute, of an encoder on another page. Encoders that have this option enabled will be indicated in the encoder assignment overview by a chain icon next to the encoder position number.
3.3.2340
21 February 2022
Fixed
- Adds support for newer versions of hardware.
3.2.2324
22 November 2021
New
- Add/remove multiple GPIO settings grid inputs/outputs at once.
- Modify Dante channel labels via Ember+.
- Modify audio input/output controls via Ember+.
- Modify audio routing via Ember+.
- Modify Dante channel labels via device webpage.
Changed
- Improved metering in dialog windows on the audio routing webpage.
- Increased double-click timeout to 500 milliseconds.
Fixed
- Model string check in recovery fails with new Dante firmware.
- Adding/removing streams does not cause audio routing page to refresh.
- Incorrect cursor type used on the copy URL button in the firmware update dialog.
- Misleading metering on main and talkback virtual busses.
- Issue when muting or unmuting a mix-point via encoder rotation.
- Headphone limiter threshold not set on reboot.
- Secondary Dante address mode radio button displayed incorrectly.
2.3.2080
4 December 2020
Fixed
- Adds support for newer versions of hardware.
2.2.1988
6 November 2019
Fixed
- Issue preventing device booting up the first time after upgrading from a 1.X to a 2.X firmware version.
2.1.1981
21 October 2019
New
-
Front Panel
-
New audio menu added to the front panel menu.
The following can be controlled for a commentator's input:- Signal level (Mic/Line)
- Pre-amp gain
- Line-up
- Phantom power
- High-pass filter
The following can be controlled for a commentator's headphones:- Attenuation
- Limiter threshold
Fixed
- Incorrect page and encoder numbering on second panel (CU4).
- Brightness menu cancel button sets LED brightness to 100%.
- Mute state of an encoder not shown on front panel page if muting via a GPI.
Changed
-
Front Panel
- Allowed for better scaling of page elements.
2.0.1915
14 August 2019
New
-
Front Panel
- The front panel can now be controlled remotely. The front panel can be controlled and configured using the front panel web page. Right-click a button to configure it. The level and pan of an encoder can be adjusted using the corresponding horizontal and vertical sliders. Double-click an encoder to mute/unmute it. Button and page locks can also be accessed in this page. The brightness of the front panel and the status LEDs can also be configured on this page by clicking on the status LEDs.
- Added a co-commentator bus to the AVN-CU4 allowing a commentator to hear all commentators but not themselves.
- Added ability to mute audio inputs and outputs via the GPIO routing grid.
Audio Routing
GPIO Routing
1.1.1802
8 April 2019
New
-
Initial Release
