AVN-DIO10-12G Dante® to 12G/6G/3G/HD/SD-SDI Embedder/De-Embedder
|
||||
 |
||||
 |
 |
 |
||
Front Iso View |
Front View |
Rear View |
||
AVN-DIO10-12G Dante® to 12G/6G/3G/HD/SD-SDI Embedder/De-Embedder
An upgrade to the extremely popular AVN-DIO10, the new AVN-DIO10-12G now adds support for the full range of SDI standards from SD-SDI through to 12G-SDI. The AVN-DIO10-12G can be used for simultaneous embedding and de-embedding of up to 64 channels. This simple plug and play audio/video interface provides a convenient and elegant method of connecting 12G/6G/3G/HD/SD-SDI equipment to the Dante® AoIP audio network.
The AVN-DIO10-12G takes an SDI feed, de-embeds up to 64 audio channels and places them on channels 1-64 on the Dante network, mapped using Dante Controller. It simultaneously takes the 64 input channels mapped to the device on Dante Controller and re-embeds them onto the SDI output.
The unit can operate in either loop through mode where the input is fed to the output, or in generator mode where the input and output are completely independent to each other and the SDI output signal is provided by an integrated SDI video generator. This allows the unit to operate as an embedder only, without the need of an existing SDI feed, or as a separate de-embedder and embedder. In this mode, the input and output can be different formats. This is fully configurable through the web UI.
The unit supports both 48kHz and 96kHz sample rates in the embedded audio allowing for different sample rates in the de-embed and embed paths. When operating at 96kHz sample rate, the number of channels within the SDI signal are halved. A single group carries two channels rather than the four available at 48kHz.
Other controls provided through the web UI allow embedding of Dante channels onto the SDI output per channel pair and there are two modes of operation: Insert Mode enabled allows embedding to overwrite existing SDI audio selectively per channel pair. Insert Mode disabled clears any incoming audio channels on the SDI output and then allows selective embedding onto the SDI output per channel pair.
Test Tone mode allows 1kHz, 2kHz, 3kHz and 4kHz signals to be output on channels 1 to 4 respectively, for any group where embedding is enabled. There is also a test tone mode for the de-embedder outputs where a 1KHz tone is placed on the transmitting Dante® channels. This is so that downstream SDI audio outputs and inputs can be tested without the need of Dante® or SDI sources.
It’s powered by Power over Ethernet (PoE), using Neutrik® EtherCON connectors, with primary and secondary ports for power and data redundancy. The AVN-DIO10-12G uses the latest Audinate Dante® chipsets so is AES67 and Dante Domain Manager® compliant. There are front panel LEDs to indicate network clock status, SDI lock status, AoIP Primary and AoIP Secondary link status, PoE Primary power and PoE Secondary power active.
Up to 3 of the AVN-DIO10-12G units can be rackmounted in the 1U AVN- DIORK.
- 1 x 12G/6G/3G/HD/SD-SDI input.
- 1 x reclocked 12G/6G/3G/HD/SD-SDI output.
- 64 channel embedder.
- 64 channel de-embedder.
- Dual redundant Primary and Secondary Dante network ports using Neutrik EtherCon® Ethernet connectors.
- Powered via PoE (Power over Ethernet) with PoE dual redundancy.
- Fully Dante compliant device.
- AES67 compatible.
- Dante Domain Manager compliant.
- Web interface for configuration.
- Clock, SDI Lock, PoE and Link LEDs.
- Overwrite or insert into existing SDI audio groups.
- SDI video generator built in.
- Independent embed and de-embed paths.
- Test tones available on both embedder and de- embedder paths.
- SDI audio sample rate support at 48kHz and 96kHz.
- All available Dante sample rates supported.
- Sample rate conversion of audio between Dante and SDI.
- Dante clock domain can be optionally synchronised from the SDI clock.
- 3 x units rackmount in the AVN-DIORK.
Technical Specification For AVN-DIO10-12G |
|
SDI Input |
|
| Input Impedance: | 75Ω Unbalanced |
| Return Loss: | <15 dB @ 1.5 GHz |
| SDI Supported Standards: | 270Mbps SMPTE-259M-C (SD) |
| Supported Video Formats: | 525/59.94 (SMPTE-125M) |
| Embedded Audio: | 48kHz and 96kHz, synchronous |
| Supported Image Mapping: | SMPTE-425M-AB |
SDI Output |
|
| Output Impedance: | 75Ω Unbalanced |
| Alignment Jitter: | <0.2UI |
| Output Level: | 800mV ±10% |
| Return Loss: | <15 dB @ 1.5 GHz |
| SDI Supported Standards: | 270Mbps SMPTE 259M-C (SD) |
Supported Video Formats |
Output follows input |
| Supported Video Formats (Generator): |
525/59.94 (SMPTE 125M) |
| Embedded Audio: | 48kHz, synchronous |
Latencies |
|
| Video | |
| SDI Loop-through: | <1 Line |
| Audio | Example latencies using an AVIOAES and Phabrix SxE with SDI and Dante sample rates at 48kHz and 1ms latency setting. |
| Embedding: | AVIOAES to DIO10-12G to Phabrix SxE |
| De-embedding: | Phabrix SxE to DIO10-12G to AVIOAES |
Network and AoIP |
|
| AoIP Standard: | Dante |
| Channels: | 44.1/48kHz - 64 receive, 64 transmit |
| Flows: | 32 receive, 32 transmit |
| Sample Rates: | 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz |
| Encoding: | PCM 16, PCM 24, PCM 32 |
| AES67 Support | Yes |
| Connectivity: | 2 x etherCON (RJ45 compatible) |
| Speed: | 1Gbps or 100Mbps (1Gbps recommended) |
| Network Modes: | Switched or redundant |
| Dante Domain Manager Ready: | Yes |
| Clock Source: | Internal (PTP Leader), Network PTP Leader |
PoE Power |
|
| Standard | 802.3af |
| Redundancy | Yes |
| Class | 0 |
| PD Power Range | 0.44 W to 12.94 W |
| Typical PSE Power Usage | 6 W |
| Max PSE Usage | 15.4 W |
Equipment Type |
|
| AVN-DIO10-12G: | Dante to 12G/6G/3G/HD/SD-SDI Embedder/De-Embedder |
Physical Specification |
|
| Dimensions (Raw): | 14.0cm (W) x 13.6cm (D) x 4.2cm (H) |
| Dimensions (Boxed): | 17.8cm (W) x 17cm (D) x 5.6cm (H) |
| Weight: | Nett: 0.36kg Gross: 0.55kg |
Accessories |
|
AVN-DIOMT |
AVN-DIO Large Unit Underdesk Mount |
